Search Results: "pollo"

26 January 2009

Andrew Pollock: [life] Too much deja vu

Seriously, every time Sarah has surgery, it all goes pear shaped. The bottom (last time it was towards the top) of Sarah's incision from her recent wire removal surgery was looking a bit red, swollen and hard on Friday, so she went in to the clinic at got them to take a look at it. They decided that a knot in the sutures was trying to work its way out, and causing inflammation or something, so just like last time, they decided to reopen the incision a bit. They did that, and cut the knot out, and rather than packing with gauze, they just taped the small opening closed with some steristrips and covered it with gauze and sent her on her way. Somewhat fortunately (for me) Sarah went into the clinic during the day while I was at work, so I missed participating in the fun and games. They didn't use any local anaesthetic, but Sarah said it didn't hurt too much. That night, though, she was in a reasonable amount of pain, again, similar to last time, except it was a band across her upper abdomen, below her breasts, instead of chest pain. Mindful of the staph infection disaster from last time, we trotted off to the ER on Saturday afternoon, hoping to nip this in the bud. They did some blood work, which came back clear, and gave her some IV pain medication, which didn't seem to do much, and were generally scratching their heads as to the cause of the pain. Fortunately, one of the surgeons involved with Sarah's wire removal from 2.5 weeks previously happened to be on call, so he got called in. He had a bit of a poke around the opening with a long cotton bud, and declared that it was possibly infected, because there was a bit of cloudy fluid discharged when he poked it in. Oh, and the cotton bud disappeared a good centimetre or more under the skin further up the incision, which indicated an abscess was forming. So, for the second time, I got to watch my wife being cut open with a scalpel. I think the local anaesthetic injections were the most painful part for her. He opened the incision up a bit further, and packed it with some Betadine-soaked gauze, and we got sent home with the same instructions as last time this happened: I had to repack the wound with saline-soaked gauze two to three times a day and let it heal from the bottom up. She was also prescribed some antibiotics. She's got about a 2cm incision just below her breasts. It looks a lot deeper than the hole from last year's incision. So we got home about 6pm last night, and went to bed around 11pm. Sarah lasted a couple of hours before she woke up in even more pain than before. She called up the hospital and had the same surgeon paged, and he advised her to come in to the ER again. So at I think about 2am, we headed back. They took some more blood, did a CT scan, which came back clear, and decided to admit her. They're giving her IV antibiotics and pain medication. Initially she didn't want to have any more IV pain medication because it didn't seem to be working, and it tends to make her nauseous. She wasn't keen on dealing with throwing up with the amount of pain she was having. It hurt to move as it was. With a mixture of IV anti-nausea drugs and the IV pain medication, the pain has finally come under control though. She did have one bought of vomiting this evening, which didn't seem to cause her too much discomfort, and she's getting in and out of bed more comfortably. They're going to keep her in overnight. She has a post-operative followup tomorrow in the clinic, so I expect they'll keep her in the hospital until at least then, depending on how things go. Her cardiologist, intimately familiar with last year's debacle, dropped in this afternoon. He's wondering, given how this has happened twice now, if Sarah has some sort of allergy to the type of absorbable suture they've used. Apparently there are different types of sutures, so if she ever has any other surgery, we'll have to get them to try a different type It'll be interesting to see how she goes tonight, as the pain seems to get worse overnight. She hasn't had any IV pain medication since about 1pm, and she wanted to see how she goes without it, because if she gets discharged tomorrow, she'll have to rely on oral stuff anyway. I think it definitely gets harder for her to manage her pain when the pain is causing her to lose sleep. She can only deal with having a couple of night's worth of bad sleep before it all gets too much. So I'm really hoping she gets a good night's sleep tonight. Not that hospitals are renowned for that...

17 January 2009

Andrew Pollock: [tech] USB power switch, part 2

Continuing with my mission to control the power to some dumb USB-powered lights... Dann Frazier confirmed my theory that a USB hub would indeed do the job. I'd already found the hub-ctrl.c program he mentioned, but couldn't get it to work with my built-in USB ports of my laptop. It seems it all depends on whether the hub will support per-port power switching or not. (lsusb -v will tell you). So off to the mighty institution that is Fry's Electronics I went. The first two attempts failed, as did a borrowed hub. It seems most (at least the cheap one) use a Genesys Logic chipset, which does not support per-port power control. Fortunately I chose products that weren't in blister packs, so I was able to return them to Fry's in as-new condition and try again. Now that I knew USB hubs would do the trick, I did some more targeted searching, and found this thread where someone had been messing around with hubs to do what sounded like what I wanted. (Incidentally, this email in the thread also provided a nice looking Python program. I'm going to look at refitting it to use the "real" Python USB module.) I emailed the poster to ask him what brand of hub he was using. The answer was the Linksys 4-port hub So I managed to track down one of them last night. Yes, it works, but the downside is the hub itself requires external power, which is a bit unfortunate. Not only do I need to use a hub to make these lights software controllable, I have to plug the hub into a power outlet. Bleh.

16 January 2009

Andrew Pollock: [tech] On filesystem layouts

Wouter's post prompted me to write this... I find it particularly strange to have a single filesystem for everything, especially so on a laptop. I worked with a guy once who had the single filesystem (I think it was ext2 or ext3), and his laptop crashed, and the filesystem was trashed so badly from the crash (I remember: it was a PowerBook, so I don't know if that had anything to do with it) that it was a write-off. One of the reasons I use multiple filesystems apply just as much to a laptop as to anywhere else: loss/damage compartmentalisation. If one of my filesystems decides to eat itself, odds are I can still get the others back. Wherever I go, I tend to have a root filesystem, one for /usr, one for /var, one for /tmp and one for /home. If it's a server, I may have a separate one for /srv as well. I always use LVM, and with ext3 supporting online resizing these days (well online enlarging at least), it's not a big problem to leave some logical extents unallocated, and just grow whichever filesystem needs it as it needs it.

Michael Casadevall: Re-enginneering my network ...

As I move to having more and more machines on my internal LAN, I felt the time had finally come that I sit down, and rebuild my network to take advantage of things such as gigabyte networking, LDAP, single-user sign on, and so forth. I'm doing partially for fun, and partially because its an interesting experiment to see how Linux from an IS environment compares to a Windows 200x IS environment (one of my former jobs was a 2000/XP/2003/Vista sysadmin position).

So, here's my current network setup
blacksteel <- *wireless* ---------------------------------------------- cerberus <-> Internet
/
dawn <------ *wired*-----------------------------------------------------
/
360 <---- *wired* -----------------------------------------------------

Online machines:
cerberus - WRT51GS
backsteel - My laptop
dawn - Development machine
360 - Xbox 360, used to play media from blacksteel

Offline machines (aka, machines I have, but haven't fired up since moving:
helios (PowerMac G4)
apollo (old Dell P3)
junker (RS/6000 rescued from the dumpster, might be dead)
alexandria (NSLU2; gave up its plug for dawn)
coldfusion (Coldfire Board, might be dead; ethernet controller is faulty, but might be able to use a USB based one to breath some life into it; can't autoreboot due to built in bootloader not supporting it; and no JTAG to sanely change the default bootloader).
siren (old MacBook Pro, has a dead internal HDD, but runs fine from an external hard drive. Was my Debian test box until its HDD went to dawn)
exodius - second WRT54GS used to be part of a WDS bridge.
unnamed dev box (not here yet, but likely soon).

Of all these machines, only apollo has a wireless card which ATM is non-functional. In addition, the wired bits of my network are 100Mbps, with a g based wireless hotspot (WPA secured). Futhermore, blacksteel, helios, and siren have gigabyte ethernet. apollo has 100MBps ethernet card. alexandria and dawn have 10MBps, which is painful, especially for NFS root.

I'll drop another 1Gbps NIC into apollo, replacing its wireless card, and give dawn, alexandria, and maybe coldfusion USB based NICs once I get around to resurrecting systems (alexandria and coldfusion don't have hard drives at the moment)

What I would like to do is use an Linux-based router and replace Cerberus. Helios has two gigabyte NICs, so it will take up this duty, as well as provide DHCPv4, and radvd (for IPv6) for the internal network. It's an old computer, and has an onboard model, and its position in my apartment will be close to a phone jack; maybe I'll set it up so I can dial in from outside the LAN in case something goes down (although my phones here are VoIP based so I dunno how useful that's going to be :-)).

Another box (I might task this to apollo, or helios) will run LDAP and NFS services, providing both a netboot based installation with preseed for fast re-installation, and NFS home folders for all machines except blacksteel (unless someone knows a great solution for having a laptop sync NFS and local home folders. helios will run mail, news, and any other untrusted net facing services, with everything else shielded behind it. All machines will run IPv4 and 6.

Anyway, this is the start of my plan in a nutshell, and I intend to continue discussion as I slowly build and implement this updated setup. Wish me luck :-).

10 January 2009

Christian Perrier: Hackergotchi meme

We're apparently starting an "update thy hackergotchi" meme with Andrew Pollock and Daniel Burrows updating their faces smiling to the world (both being much better than their previous version, indeed). I really should update mine, too, as it is: So, should I use Debconf 6, Debconf 7 or Debconf 8 mugshot? Or maybe Wouter's art (by far the most up to date when it comes at ripples and stuff)?

Gustavo Franco: slack roles!

Just uploaded some very rough slack roles in github to be used with slack. If you want to give a pull-only configuration management system a try, slack may be useful for you. It is also part of Debian for a while and may make Lenny, thanks to Andrew Pollock. He managed to package it before Alan Sundell allowed me to setup a project in code.google.com to keep it under a VCS.

slack advantage if compared with cfengine and puppet is that there's no need to have a daemon running in the client side and learn a new language to set things up. The disadvantage is that there is a central configuration in place but you can't manage from that central location (read push changes).
I plan to add more roles and polish the existing ones, I may split Debian/Ubuntu support in multiple branches as well. Let me know if you want to contribute or just want to know more about slack.

Let's wrap it up. Slack is a configuration management system maintained in code.google.com using SVN. Slack has the concept of roles to work properly and slack as is in code.google.com comes with no roles. slack-roles in github tries to fill the gap for Debian. You may need to fork it for internal usage, but I want to provide fully functional templates.

ps: Yeah, I've a laptop named trinity. duh!

Andrew Pollock: [geek] Out with the old, in with the new

My old hackergotchiMy new hackergotchi It's a new year, so why not a new hackergotchi I say? Brandon and Robin came around on Thursday night, and where there's Brandon, there's his camera, so he got a decent enough mugshot to convert into a less crap hackergotchi (after I spent a few hours fighting with the GIMP today)

Andrew Pollock: [life/americania] The Story of Stuff

Sarah brought The Story of Stuff to my attention today. It's well worth 20 minutes of your time, irrespective of where you live.

Andrew Pollock: [life] One year and five days later...

...and there was a distinct feeling of deja vu. At least the procedure itself was nowhere near as long (under 2 hours). On Thursday, Sarah had some day-surgery to have her sternal wires removed. The top one was causing her some discomfort because the skin there was the thinnest (whether that in itself was related to any of the previous incision complications remains uncertain). The surgical team popped in to pre-op to autograph their work (seriously, they initialled her chest) before they started, and asked if she wanted just the top wire removed, or all of them. We consulted the Magic Eight Ball application on my phone, and it gave a resoundingly affirmative response, so she got them all removed. Despite removing them all being a bit more surgically invasive, I think this is for the best. It means none of the other wires can cause any problems down the track requiring yet another trip to the operating room. They also did some scar revision on the top part of the scar, where it was a bit stretched (from the previous complications), so incisionally speaking, she's had almost as much incision work done as the original heart surgery. Ironically, this made the plastic surgery (laser treatment and steroid injections) she had late last year largely redundant. She took the dressing off the incision this morning, and we had our first look at it. It certainly looks a lot better than before, so fingers crossed it won't get infected this time, and the overall long-term result will look better.

6 January 2009

Andrew Pollock: [tech] On trying to use a Sansa e260 on Linux

I received a SanDisk Sansa e260 (v2) for my birthday. It was one of those presents that acquired for myself on behalf of someone else because it worked out easier that way. I bought it for cheap from Woot! I thought I'd use it to play podcasts while I'm at the gym. We've been listening to NPR for a while now, and there's lots of excellent programming, and it's all available in download for as well. Since I don't spend all that much time in the car, I'm not listening to much of it. The first mission was to upgrade the firmware. Getting the player into MSC (instead of MTP) mode with the original firmware was a little tricky, but I got there in the end. Then I had to locate the firmware in a Linux-installable format. I think I ended up resorted to using Windows, but I later found the raw firmware image without needing an installer. I'm using Rhythmbox at the moment to download the podcasts. I thought I'd try out its MTP support, just because it actually had it, but either Linux 2.6.26 has a problem with MTP, or the player is particularly flaky doing it with Linux, because I just seemed to get a pile of USB errors when connecting the device in this mode, so I'm sticking with MSC for now. Oh, and I had to put a .is_audio_player file in the root of the device to make it show up in Rhythmbox. I later discovered that it worked most optimally if I put
audio_folders=MUSIC/
folder_depth=2
in the file. I'm still trying to come up with an optimal way of managing the audio I want to listen to. It seems somewhat tedious to drag and drop all of the podcasts from Rhythmbox to the device. I kind of want some sort of plug and play auto-sync method. It seems I can't use a connection-triggered rsync, because some of the podcasts seem to get downloaded with non-FAT-filesystem-friendly filenames. Rhythmbox seems to take care of this by doing some sort of automagical renaming at transfer time. That said, not everything is showing up in the music list with sane names. There's a few things that have an unknown artist I think. That may be a deficiency in the ID3 tags of the MP3s themselves though... What I really want some way of getting home, hooking up the player and just getting what's new, without expending too much effort (at the time of hooking up the player, anyway. I'm happy to expend some effort getting to that point) The next weird thing is that the device wants to talk USB 1.1. I'm not sure what is at fault here, but I can, allegedly at least, make the device reconnect at USB 2.0 by removing and reloading the ehci-hcd module after connecting it. Here we have the device initially attached:
apollock@icarus:~$ lsusb -t
Bus#  5
 -Dev#   1 Vendor 0x1d6b Product 0x0002
Bus#  4
 -Dev#   1 Vendor 0x1d6b Product 0x0001
Bus#  3
 -Dev#   1 Vendor 0x1d6b Product 0x0001
   -Dev#   9 Vendor 0x0781 Product 0x7423
Bus#  2
 -Dev#   1 Vendor 0x1d6b Product 0x0001
   -Dev#   6 Vendor 0x413c Product 0x8103
Bus#  1
 -Dev#   1 Vendor 0x1d6b Product 0x0001
lsusb says that bus #3 is ID 1d6b:0001 Linux Foundation 1.1 root hub Then if I do a spot of presto-changeo...
apollock@icarus:~$ sudo modprobe -r ehci-hcd
apollock@icarus:~$ sudo modprobe ehci-hcd
apollock@icarus:~$ lsusb -t
Bus#  5
 -Dev#   1 Vendor 0x1d6b Product 0x0002
   -Dev#   3 Vendor 0x0781 Product 0x7423
Bus#  4
 -Dev#   1 Vendor 0x1d6b Product 0x0001
Bus#  3
 -Dev#   1 Vendor 0x1d6b Product 0x0001
Bus#  2
 -Dev#   1 Vendor 0x1d6b Product 0x0001
   -Dev#   7 Vendor 0x413c Product 0x8103
Bus#  1
 -Dev#   1 Vendor 0x1d6b Product 0x0001
Bam! It's moved over to bus #5, which lsusb says is 1d6b:0002 Linux Foundation 2.0 root hub Weird. I wonder if I should try running Rockbox on it? Seems not, it's only for v1 players. Oh well.

4 January 2009

Andrew Pollock: [tech] Feed breakage, Blosxom's shiteful RSS 0.91 implementation

(or echo "blosxom hold" sudo dpkg --set-selections) A few people had pointed out to me that my blog was appearing weirdly in Google Reader. I myself read my blog via Planet Debian and Planet Linux Australia, where it appears fine, so I hadn't noticed the problem first hand. I did some digging tonight with the Feed Validator, and I think I've figured it out. Funnily enough, it all started with a previous session with the Feed Validator... I wanted my blog to be UTF-8, with it being the new hotness and all. Blosxom was spitting it out as ISO-8859-1. I've just learned from this evening's debugging, that this is the behaviour of CGI.pm's header() function if not provided with the -charset parameter. I'd previously worked around this by defining my own content_type for the RSS and HTML flavours. In this file, I just put text/xml; charset=utf-8and text/html; charset=utf-8, respectively. Unfortunately, this then breaks Blosxom's internal HTML-escaping-for-RSS-feed code, which is conditional on the content type being XML:
if ($content_type =~ m \Wxml$ )  
        # Escape <, >, and &amp;, and to produce valid RSS
        my %escape = ('<'=>'&lt;', '>'=>'&gt;', '&'=&gt;'&', '"'=>'&quot;');  
        my $escape_re  = join ' ' => keys %escape;
        $title =~ s/($escape_re)/$escape $1 /g;
        $body =~ s/($escape_re)/$escape $1 /g;
       
This block of code was being ignored because the regex was anchored. "text/xml; charset=utf-8" didn't match "\Wxml$". Whenever I last had an attempt to make my blog's feed pass the Feed Validator, I must have edited the Blosxom source code to make this regex not be anchored. Then on November 11, 2008, I updated my Blosxom package to 2.0-14+etch1, to address CVE-2008-2236 (incidentally, there doesn't appear to be a Debian Security Advisory for this?), and my local modification got clobbered. That'll teach me to make local modifications and not put the package on hold. Blah. It seems I'm screwed, there's no way to have a well-formed UTF-8 RSS feed without requiring a source-code modification to Blosxom. I've either got to change the way the header() function is being called, or I've got to change the regex to allow me to specify a charset in the flavour file, and not disable HTML escaping. Speaking of screwed, Blosxom seems incapable of making a well-formed RSS 0.91 feed anyway. It wants to put the <pubDate> tag inside an <item>, which is a violation of the DTD. There's supposed to be one for the whole <channel>, not one per item (or "story" in Blosxom-flavour-speak). You can't just move that from the story flavour file to the head flavour file, because a pile of variables that you'd otherwise use seem to only get set on a per-story basis. Double blah. I'm starting to feel like Blosxom is outliving its usefulness, but I really do not feel like embarking on a wholesale move to a new blogging platform, I'm fairly entrenched.

Andrew Pollock: [tech] Mixing electricity and water: monitoring the cat water bowl with Nagios

(this is something I've had "in production" for many months now, I just haven't had the time or energy to do a proper write up about what I did) We have a cat water bowl, it looks like this: The cat water bowl Under "normal" circumstances, it usually lasts about seven days. So when our weekly routine is happening, we'll refill it on a Saturday whilst doing house chores, and it'll last until the following Saturday when it gets refilled. Unfortunately, sometimes our routine gets disrupted, and we forget. Sometimes, we travel and have a house-sitter, who may not pay as close attention to such things as ourselves. Once, one of our cats was licking the condensation off a chilled bottle of soft drink that was on the kitchen counter one evening, before we realised the water bowl needed refilling. Naturally, we felt like terrible pet owners. So I think it was some time around the 2008 Maker Faire, that I hatched the idea of having some sort of water sensor on the cat bowl, which would communicate to one of the various computers in house. At the Maker Faire, I bought a copy of Making things talk, and an Arduino starter kit, which consisted of a Diecimila board and a make-it-yourself proto shield. I also bought a little electronics starter kit, which consisted of a breadboard and various components, and a USB-TTL cable. I decided to use Bluetooth to communicate with the board, as I already had my MythTV setup using a Bluetooth keyboard and mouse, and it was within range of the water bowl. I decided against using Zigbee, because I didn't know anything about it, and I didn't want to add (or learn about) yet another wireless infrastructure just for this project. I should point out that I know very little about electronics. I'd never owned (or really used) a soldering iron until I embarked on this project. I took a basic soldering class at the Tech Shop, but I'd already assembled the proto shield by the time I took the class, so I'd pretty much figured it out. I had a very naive vision that I could just basically shove two wires in some water and it'd close a circuit and that would be my water sensor. Of course this didn't work, so I started hunting around on the Internet for a circuit that would do this. I happened upon a circuit (I don't seem to have retained the URL, so I can't link to it), which just consisted of a couple of transistors and some resistors. So I headed off to Fry's to try and buy the transistors I needed. I quickly discovered that I didn't have sufficient information to identify the transistors that I wanted, but I did happen to stumble upon a cheap assemble-it-yourself water alarm. It consisted of a PCB, and a transistor and some resistors and a buzzer. I bought a couple of these instead. Between studying the PCB and the circuit diagram that came with the alarm, I was able to reproduce it on my breadboard instead of on the PCB. Sure enough, placing the two probes in water closed the circuit. I replaced the buzzer with an LED so I could see what was going on. I attached the circuit to the Arduino proto shield, and had it feed into one of the digital I/O ports. I wrote some quick and dirty Wiring code so that when water not present (i.e. the circuit was open and no current was detected on that I/O port) the LED was switched on. Really at this point, I didn't need a microcontroller, I could have presumably achieved the same thing with a NOT gate. At this point, I wanted to make the sensor remotely queryable. I bought a BlueSMiRF Silver Bluetooth modem, which I attached to the TX and RX lines of the board (I first configured it by attaching the USB-TTL cable to it and using Minicom on my laptop). I extended the Wiring code to provide a rudimentary prompt, and accept a command to check if water was present. I think around this time it also dawned on me that I could use the digital I/O pins as a switch. When they're "high" they provide power. So rather than constantly running a current through the water, I only needed to briefly power up the water detection circuit, see if the circuit closed or not, and then report if water was present if it did. I much preferred this, as at the time, I was endeavouring to power the whole sensor off a 9 volt battery. I figured I'd get much better battery life if I wasn't running a current through the water the entire time. I should point out that I did some "tongue tests" in a glass of water while the circuit was powered up, and couldn't detect a difference between when the circuit was on or off. The last thing I wanted to be doing was zapping the cats! At this point, the Wiring and Arduino work was pretty much complete. I setup ser2net on the MythTV server, so that I could just connect to port 4000, and be connected to the water sensor.
apollock@icarus:~$ telnet teevee 4000
Trying 172.16.0.9...
Connected to teevee.andrew.net.au.
Escape character is '^]'.
ser2net port 4000 device /dev/rfcomm0 [9600 N81] (Debian GNU/Linux)
waterbowl> s
Water is present
waterbowl>
telnet> q
Connection closed.
apollock@icarus:~$
The Wiring code running on the Arduino board is checked in here. Next, I wanted to monitor this with Nagios. One thing I found with the Bluetooth connection was that it wasn't all that reliable. Not every connection to port 4000 resulted in a connection with the water sensor. I elected to write some standalone code that submitted results to Nagios by way of a passive check, rather than having Nagios try to actively monitor it. Again, trying to conserve energy, I decided to only check the sensor once every 8 hours. So I wrote a Python daemon, which tried to be as robust as possible. If at first it doesn't make a connection on its 8 hourly schedule, it keeps trying until it does. Nagios itself has some freshness detection for this monitor, so if no passive result is submitted within 8 hours and one minute, Nagios alerts that something is possibly wrong with the sensor itself. (The original intent was to deal with the situation where the battery went flat) This is the Nagios service definition I've got. Some of it may be unnecessary or redundant:
define service  
        host_name                       teevee
        service_description             Cat water bowl
        check_command                   check_stale!2!"Check water bowl monitor is on and reachable"
        normal_check_interval           480
        notification_interval           240
        active_checks_enabled           0
        check_freshness                 1
        freshness_threshold             28860
        max_check_attempts              1
        check_period                    24x7
        use                             generic-service
        stalking_options                o,w,c
        contact_groups                  everyone
 
The code for the Python daemon is checked in here. So everything was going swimmingly, apart from I couldn't get even 24 hours of monitoring on my conservative 3 times a day schedule, and the Bluetooth modem configured for all of its power saving options, and the water sensor itself only being powered on when it was performing a check. There wasn't much more I could do to try and reduce power consumption, at least with my limited electronics knowledge. Perhaps using Zigbee instead of Bluetooth would have helped, but I still think I'd have been going through 9 volt batteries more quickly than I'd have liked. I also had a brief foray into solar powering the board. I thought maybe the lighting in the house would be sufficient to power the board. Of course this didn't work out. I'd also have needed to make the code running on the board more self-sufficient, and have it just provide a water status indication whenever it had enough power to do so, instead of being a fairly dumb device like it currently is. This all felt a whole level more complicated, and out of my league, and I wasn't interested in attempting this sort of remote-sensing exercise at this time. The Arduino board can also be powered by USB, so as I already had some long USB type A to type B cables (that had funky lights in them to boot), I decided to just get a wall wart that had a USB type A receptacle, and powered the Arduino board that way. So much for being completely "wireless". (I could have also gotten a general purpose DC power supply that was capable of spitting out 9 volts, but I doubted I'd get one with a sufficiently long cable, which is why I went for the USB-powered option, as I already had a cable long enough) Speaking of wires, the most challenging part was the probes for the water sensor. As they were going to be permanently in the cats' drinking water, I didn't want to contaminate the water with them. I figured plain untinned copper wire would be okay, since water pipes are copper. Finding untinned, unstranded copper wire was a real challenge. I started out using some FM antenna cable, but that was stranded, and the shielding was a nightmare to strip. It was also reasonably difficult to make go where I wanted it. What I really wanted was something more solid, that would flex and stay where I put it. I cannibalised a spare IEC power cable, but it was also stranded copper wire. I finally managed to obtain some solid-core CAT-5 cable from a hardware store, and this has worked exactly as I wanted. I haven't done any further work on the setup since getting the CAT-5 cable for the probe. Further improvements that I'd like to do at some point: The finished product I had a lot of fun with this project. I had a real sense of achievement, being able to go from concept to completion, and learn a few things about electronics along the way. I'm normally not a fan of messing around with hardware. Some photos of the project are here.

2 January 2009

Andrew Pollock: [debian] Online dependency maps for Debian packages

This is pretty cool. I think the craziest dependency map for a package I maintain is the one for argus-server. (Discovered via LWN)

1 January 2009

Andrew Pollock: [geek] Connect-a-desk

OMG OMG OMG!!! I just discovered the connect-a-desk I had a crazy idea for something exactly like this a couple of years ago, when I was in Las Vegas for Christmas, in a line for a buffet on Christmas Day, and on call. I was trying to juggle a laptop and deal with something I'd been paged about whilst still standing in line. I'm so buying one. I could work on a treadmill!

Andrew Pollock: [tech] USB power switch?

I bought these USB powered lights from Woot! recently, with grand plans of using them with a continuous build/test/install rig to provide visual notification of when a build/test/install completed or failed or something. Somewhat to be expected for the price, they merely draw power from the USB port, and have a physical switch on each light. I want something software controlled though. There's something in /sys/bus/usb/devices/*/power/level that looked promising, but seems to be a red-herring (at least for non-devices. I was able to turn off a USB mouse and a Bluetooth adapter this way) What I'd like (and it probably exists, I just have to find it), is a USB device that presents itself to the operating system, and its sole purpose is providing pass-through power to a USB A-type receptacle on itself. This would then be manageable by the operating system. What I'm possibly trying to say here is a small, specialised, one port USB hub. Hmm... I'll have to see if I can borrow a USB hub from someone to test this theory. I've never had a need to own one.

31 December 2008

Andrew Pollock: [tech] On unlocking a Vonage-provided Linksys RTP300

Well that was a bit of process. The best set of instructions I found were here. I think a lot of the other instructions I found assumed you were at firmware version 1.00.62. The CYT unlocker program seems to only work with this firmware version. The CYT unlocker program is a Windows console-mode program. It seems to run under Wine, but I switched to Windows before I realised that possibly my problems running it under Wine were related to the firmware version on the RTP300 and not a problem talking to the network. All of the remaining steps on the above page could have been performed on Linux. In fact, the CYT unlocker program merely makes a HTTP POST to a specific URL (and I think it could just as easily be an HTTP GET) and then starts up a webserver on port 2400 to hand an XML blob of provisioning information when the RTP300 requests it as a result of the HTTP POST. A Linux version would be easy to implement. In all of the futzing around, I noticed this gem in the HTML source of the web interface:
*********************************************************
*   Copyright 2005, CyberTAN  Inc.  All Rights Reserved *
*********************************************************
This is UNPUBLISHED PROPRIETARY SOURCE CODE of CyberTAN Inc.
the contents of this file may not be disclosed to third parties,
copied or duplicated in any form without the prior written
permission of CyberTAN Inc.
This software should be used as a reference only, and it not
intended for production use!
Now that I've unlocked it, I guess I should try and make it talk to my Asterisk box...

Andrew Pollock: [tech] Goodbye Vonage, hello T-Mobile@Home

When we first moved to the US, I wanted to try and do the telecoms and Internet stuff as cheaply as possible, while still trying to be technologically "fun" as well. I elected to get the cheapest home phone line (local calls only) I could get with AT&T (then SBC) (which is still remarkably expensive) so that I could get DSL (which, while three times faster than what I'd had previously in Australia, was still not that fast). (I went for DSL over cable because I'd heard horror stories about Comcast's reliability, and also they weren't cool with running servers or inbound services, Sonic is, and is a great ISP). I chose Vonage for US long-distance, I think because I'd heard of them previously, and was interested in trying out VoIP. We initially used Vonage for calling Australia as well, until I played around with Engin, and then deployed Asterisk. Anyway, I've been a loyal Vonage customer for exactly three years. The truth is, we hardly make any US long distance calls. We've got friends in Phoenix (hi Craig and Sarah!) that we call infrequently. I guess there might be the odd cell phone that isn't considered a local call, but we tend to use our cell phones more than the home phone anyway... So we were a very cheap $14.99 a month for Vonage. So when I called T-Mobile to purchase a SIM card for the Android Dev Phone 1 I'd been recently given, the opportunity to have their T-Mobile @Home in place of Vonage, for an extra $9.99 on top of what I was paying for the cell phone line seemed like worthwhile cost saving. I have no attachment to the incoming number for the Vonage line, we give out the AT&T land line number to people as our "primary" home number. Later that day, Vonage announced they were increasing their monthly fee from $14.99 to $17.99, which made the decision seem all the more prodigious. I did a spot of research while I was waiting for the @Home box to ship to me, and it turns out that they have a wireless router and non-wireless router option. They hadn't specified what I was getting at order time, and I was hoping I'd get the non-wireless router, since I already had an access point I was perfectly happy with it. As luck would have it, I received the wireless router model (a Linksys WRTU54G-TM). I'd mentally prepared myself to be receiving just another Linksys RTP300, like what Vonage used, and so I was quite surprised by the differences in technology used. It's been a while since I tried to do any reverse-engineering of the Vonage ATA, but I think from memory, it was essentially that: an ATA. It talked SIP back to Vonage. My DSL provider gave me a few static IP addresses, so when I got it, I just allocated one for Vonage, and did a static NAT through my firewall to for it, and everything just worked. It was fairly apparent that the WRTU54G-TM was nothing at all like this (given it was also an access point). It takes a GSM SIM card (up to two in fact), which I presume has all of the provisioning information on it. I was initially worried that I was going to need to completely rejig my network to accommodate it. I guess the SIM card approach means there's no customer specific provisioning that presumably otherwise needs to be done to the device itself, and they can just ship vanilla devices. I presume the Vonage RTP300 had some sort of customer-specific configuration, because I never had to do anything. I briefly toyed with the idea of running two access points, and having a "guest" wireless network, but I am interested in reducing heat and power consumption in my linen cupboard, so I decided to try and just swap over to using the WRTU54G-TM as my access point, retiring my Linksys WAP54G. So that's exactly what I sat down to do last night. Sometimes in their efforts to make these things "simple", they end up making things more complicated. What I wanted to do was just plug the "Internet" side of the device into my internal network, have it get an IP address with DHCP, and then let me get on with configuring it. The "advanced" setup instructions talked about the box having a default IP address of 192.168.0.1 ("or try 192.168.24.1 if that doesn't work"). I figured the DHCP IP address would override that, so I was trying to hit the IP address I could see the unit had picked up from my DHCP server. No response from the HTTP server. I could see it replying to ARP requests, and I could see what appeared to be an IPsec NAT-T connection. After some fiddling around, I twigged that I was trying to manage it over the Internet port, and any device worth its salt was going to be very hardened out of the box on what it expected to be the raw Internet-facing side, so I plugged my laptop directly into one of the four Ethernet ports that it also had, and then I could hit the 192.168.0.1 IP address and access the management interface. It never occurred to me prior to fighting with getting the WRTU54G-TM configured, that the RTP300 might have been more than a black box, as I'd never tried plugging anything into the "inside" ports on it, mainly because I'd never intended to use it as a router or a switch. Out of the box, the WRTU54G-TM was configured to be a router, which I didn't need, and it was configured to be a DHCP server for 192.168.0.0/24, which I definitely didn't want. An interesting side-effect of putting it into bridging mode was the MAC address changed (to the one that was printed on the unit, which was not how out of the box it presented itself). I have no need or intention of plugging anything into the "inside" Ethernet ports on the WRTU54G-TM, as I have a separate switch for that, and indeed I run my wireless network on a different interface of my firewall to my wired network. Fortunately I was able to enable the management interface via the "Internet" interface. The added benefit of the device doing NAT-T is I don't need to allocate an IP address to it for the VoIP stuff it work, it all just works fine without it, so I've freed up an IP address, removed two devices from my linen cupboard, added one new one, and saved some money. Woot! Next, just because I can, I'm going to try and break into the RTP300 and see if I can reconfigure it as a general purpose ATA to talk to Asterisk. There's evidence it's possible. It's otherwise of no further use to me. Even if I get it working with Asterisk, it's not of a lot of use to me. Maybe I can send it to a family member, and they can call us over the Internet for free instead of for the cost of a call to Brisbane...

28 December 2008

Andrew Pollock: [life/americania] The Civic Musical Road and Other Adventures

It's not a holiday without a road trip, especially with petrol prices being lower now than they were three years ago when we arrived here. So we headed off on Christmas Day for San Simeon, with the general plan to tour Hearst Castle on Boxing Day (which isn't a public holiday in the US, but is a company holiday), and then head to Thousand Oaks, to visit a friend of Sarah's who also had heart surgery this year, and then head home. We'd hatched this plan a few months ago, and afterwards, saw a news piece on the "Civic Musical Road", and when we discovered it wasn't too far from Thousand Oaks in the grand scheme of things, we decided to throw that on the itinerary as well. I found a five-part "making of" documentary on YouTube, along with what I presume is the original commercial, and of course, we had to record the experience. Making of, part 1 Making of, part 2 Making of, part 3 Making of, part 4 Making of, part 5 Presumably the final commercial Our experience (on the relocated version)

20 December 2008

Andrew Pollock: [tech] The Bad Block HOWTO hurts my brain

Seriously. It reads more like a worked example, without enough of the underlying theory. It doesn't help that I have a slightly more complicated situation, in that I have a filesystem on a logical volume that spans 6 physical volumes. So maybe writing all of this down will help... I know the disk with the problem: /dev/sdc I know the LBA of the sector where the rot starts: 754238963 I know that the physical volume is on /dev/sdc1 and that the partition starts at sector 63 (via sfdisk -luS /dev/sdc) Therefore, within /dev/sdc1, we're talking about block number 754238899 (754238963 - 64) I know the physical extent size is 4096 Kb (via pvdisplay -c /dev/sdc1 awk -F: ' print $8 '). In LBA block size this becomes 8192 (2 x 4096) I know the physical extents start 192K (into the partition, presumably) (via pvs -o+pe_start /dev/sdc1) This is where the Bad block HOWTO starts to quicken the pace a bit on me... I'm supposed to take the physical partition's bad block number (754238899) and divide it by the size of the physical extent (in LBA block size) (8192). So that'd be 92070. This is where I think I end up completely departing the HOWTO, because my filesystem spans multiple physical volumes. Here's my general musings... lvdisplay --maps /dev/data/srv tells me this about /dev/sdc1:
  Logical extent 272326 to 391559:
    Type                linear
    Physical volume     /dev/sdc1
    Physical extents    0 to 119233
So I'm inferring from this, given that I know I want physical extent 92070 of this device, that this corresponds to logical extent 92103 (again, I'm expressing this in LBA block size, so that's (272326 / 8192) + 92070 So now I supposedly know the logical extent (in LBA size) of the bad block. Now what? I think I'm wandering up too many layers, closer to the physical filesystem, but I'll continue wandering around... So presumably at this point, I just want to convert the logical extent to an actual filesystem block number. Maybe the logical extent number divided by the extent filesystem block size divided by the LBA block size? 92070 / (4096 / 512) = 11508. That feels awfully low though. The dd test suggests this is incorrect. At this point I'm feeling fairly lost. If someone out there is reading this, and they've done this before, I'd love to hear from you.

Andrew Pollock: [tech] Reflections whilst waiting for fsck, part 2

So it turns out if you wait long enough, you do get to piece the information together:
.
.
.
Too many illegal blocks in inode 209158151.
Clear inode? yes
Restarting e2fsck from the beginning...
/srv contains a file system with errors, check forced.
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Entry 'denemo_0.7.7-3.1_hppa.deb' in /debian/pool/main/d/denemo (211845291) has deleted/unused inode 209158151.  Clear? yes
.
.
.

Next.

Previous.